Početna > R/C DELOVI - OPREMA > Engines/El. motor's > BRUSHLESS ESC

BRUSHLESS ESC

za sve ostale INFO: Zvrcc.. 069/1029252 Zajko

Turnigy 30A BRUSHED ESC  
snizeno !!!   15 EUR
Got an old brushed motor laying around and want to put it to good use?
The Turnigy brushed ESC is an excellent speed controller with a linear throttle curve,Lipoly/NiMh ready and programmable braking.
Features:
The break function can be turn on/off by the jumper
Battery type can be chosen by a jumper
For Lipo the threshold for each cell is 3.0v, less than the threshold ESC will gradually reduce the output power
PWM frequency is 2KHz
Over heat protection over 110C
Throttle signal loss for 1sec will gradually reduce the output power, after 2sec completely cut-off 
Spec.
Cont Current: 30A
Burst Current: 40A
BEC Mode: 5v/1A
Lipo Cells: 2-3
NiMH : 4-10
Weight: 21g
Size: 45x21x8mm

Turnigy Brushless ESC 85A w/ 5A SBEC      60 EUR

Built with imported N-Channel mosFETs and an ultra fast Atmel MCU & heartbeat

make this a high performance ESC with excellent sync capabilities. This ESC has a 5A SBEC for solid reliable servo power.

Programmable via an R/C controller.It allows you to program all functions to fit your specific needs, which makes

it efficient and user friendly.

Features: 
Extremely low internal resistance Super smooth and accurate throttle linearity Over heat and over-load protection 
Auto shut down when signal is lost or radio interference becomes severe for more than 2 seconds. Supports high RPM motors 
Power arming protection (prevents the motor from accidentally running when switched ON).New Advanced programming software
Programming features:
Brake setting (we recommend using brake for only folding props applications).
Battery type(LiPo or NiCd/NiMh).Low voltage cutoff setting.Factory default setup restore.Timing settings
(to enhance ESC efficiency and smoothness).Soft acceleration start ups (for delicate gearbox and helicopter applications)
Governor mode(for helicopter applications).Motor rotation( clockwise\counterclockwise).Switching frequency.Low voltage cutoff 
type (power reduction orirnmediate shutdown)
Factory default settings:
Brake:  off..   Battery type Detect:  LiPo with Automatic Cell. Low voltage cutoff threshold:  Medium (3.0V/65%) 
Timing setup:  Automatic   Soft Acceleration Start Up:  Medium Governor mode :  OFF Frequency :  8kHz 
Low voltage cutoff type:  Reduce power
Spec.
Cont. Current: 85A   Burst Current: 100A  Battery: 2-6 Cell Lipo / 5-18 Cell Ni-XX  SBEC: 5.5V/ 5A Output
Size: 52*34*20mm  Weight: 60g
Turnigy Programming card for Tz85A ESC    15 EUR
Programming features:
Brake setting (we recommend using brake for only folding props applications).Battery type(LiPo or NiCd/NiMh).
Low voltage cutoff setting.Factory default setup restore.Timing settings (to enhance ESC efficiency and smoothness) .
Soft acceleration start ups (for delicate gearbox and helicopter applications).Governor mode(for helicopter applications) .
Motor rotation( clockwise\counterclockwise).Switching frequency. Low voltage cutoff type (power reduction orirnmediate shutdown)
Factory default settings:
Brake:  off Battery type Detect:  LiPo with Automatic Cell  Low voltage cutoff threshold:  Medium (3.0V/65%) .
Timing setup:  Automatic .Soft Acceleration Start Up:  Medium .Governor mode :  OFF. Frequency :  8kHz.
Low voltage cutoff type: Reduce power
Hobby King 60A ESC 4A UBEC               45 EUR
Specs:
Constant Current: 60A  Burst Current: 80A  Battery: 2-4S Lipoly / 5-12s NiXX  SBEC: 5.5v / 4A  Motor Type: Sensorless Brushless
Size: 70 x 32 x 17mm  Battery Wire: 14AWG  Motor Wire: 14AWG  Weight: 61g
Programming Functions:
Battery Type: Lipo /NiXX  Brake: On / Off  Voltage Protection: Low / Mid / High  Protection mode: Reduce power / Cut off power
Timing: Auto / High / Low  Startup: Fast / Normal / Soft  PWM Frequency: 8k / 16k  Helicopter mode: Off / 5sec / 15sec (Start up delay)

Hobbyking SS Series 50-60A ESC       40 EUR

The Hobbyking SS series comes with a limited range of programming functions and are designed to be plug-n-play.
A perfect ESC for those looking for something simple to use and economic.

Weight: 63g  Size: 55x35x8mm  Cells: 6-20Ni MH ~ 2-7S Li Po  Max Current: 50A Burst: 60A No BEC Timing: 1/7/15/30 programmable  PWM: 8/16K

Constant current 50A Max 60A <10S     Li-Poly 2-7 cells Ni-MH 6-20 cells     Low Resistant 0.0014 Ohms;
Dynamic Braking   BEC: opto    Auto shut down when lose signal 
Slow down at 3.0V per cell Lipo, Cut-off at 2.9V per cell Lipo 0.8V NiMh
 Battery settimg    Throttle Range  Brake setting 4 options     Timing Mode Setting: 1 / 7 / 15 / 30   PWM setting: 8K/16K

Hobby King 40A ESC 4A UBEC         35 Eur

Constant Current: 30A  Burst Current: 40A   Battery: 2-4S Lipoly / 5-12s NiXX   BEC: 5v / 3A   Motor Type: Sensorless Brushless   Size: 54 x 26 11mm    Weight: 32g

Programming Functions:
Battery Type: Lipo /NiXX  Brake: On / Off  Voltage Protection: Low / Mid / High  Protection mode: Reduce power / Cut off power  Timing: Auto / High / Low   Startup: Fast / Normal / Soft   PWM Frequency: 8k / 16k
Helicopter mode: Off / 5sec / 15sec (Start up delay)

HobbyKing ESC Programming Card     20 EUR

Suits The following HobbyKing ESCs:

Hobby King 80A ESC 4A SBEC     Hobby King 60A ESC 4A UBEC   Hobby King 30A ESC 3A UBEC   Hobby King 20A ESC 3A UBEC

Hobby King 18A ESC 3A UBEC               22 EUR

10-Amp Pro Brushless ESC by E-FLITE                     18 EUR

Key Features

• Up to 10-amp continuous current with proper air flow
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable low-voltage cutoff with settings for 2-cell Li-Po (6V), 3-cell Li-Po (9V) or 70% of battery starting voltage
• Programmable throttle input range (1.1ms–1.9ms or Auto Select)
• Auto motor shut down if signal is lost or there is interference
• Programmable timing—2 user-selectable ranges for use with a large variety of brushless motors
• Pre-wired connectors—JST on battery input and 2mm female gold bullets on motor output leads
• Soft start

Overview

This controller has been designed for use in radio control aircraft and to support continuous currents of up to 10 amps when using 2–3 cell Li-Po battery packs and up to 4 sub-micro servos. Standard features include advance BEC and safe power-arming along with programmable features such as low-voltage cutoff, braking, timing and throttle input range. 

Specs

40-Amp Lite Pro Switch-Mode BEC Brushless ESC by E-FLITE   70 EUR

 Key Features

• Up to 40-amp continuous current with proper airflow, 55-amp burst current
• 5-volt Switch-Mode BEC circuit capable of 2.5-amp continuous current
• Drives up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input voltage
• 3S-6S LiPo or 9- to 18-cell Ni-MH/Ni-Cd input voltage
• Programmable motor braking
• Safe power-arm mode prevents accidental starts
• Programmable soft start for helis and airplanes
• Auto motor shutdown if signal is lost or there is interference
• Programmable timing – 5 user-selectable ranges for use with a larger variety of brushless motors
• Programmable throttle input range (1.1–1.9ms or 1.2–1.8ms)
• Heli mode for starting the motor with a low speed ratio
• Pre-wired connectors-E-flite EC3 connectors on battery input and 3.5mm female gold bullets on motor output leads

Overview

For up to 40 amps of continuous current with proper airflow, the E-flite 40-Amp Lite Pro SB brushless ESC delivers. It drives up to 7 analog or 6 digital servos with the BEC on any recommended input voltage. This brushless ESC includes programmable motor braking, soft start for helis and planes, timing, throttle input range and low voltage cutoff. It also features auto motor shutdown in case of lost signal or interference. The safe power-arm mode prevents accidental starts.  All the great features of E-flite's popular 40-Amp Pro SB Brushless ESC, in a lighter weight package perfect for use in large-size park flyers and mid-size models where space and weight are more critical.

Specs

Tech Notes

Servo Ratings with BEC Enabled:

Drives up to 7 analog or 6 digital standard-sized servos with the BEC on any recommended input voltage. This also includes up to 7 standard analog or 5 standard digital and 1 retract servo, perfect for 25-sized warbird conversions. 
Some servo combinations we have tested in various models include: 

• 4 JR SPORT MN48 (JSP20040) analog mini servos—E-flite Diamante 25e ARF and J-3 Cub 25e ARF 
• 4 JR DS3421 (JRPSDS3421) digital mini servos—E-flite Eratix 3D 25e ARF 
• 7 JR MC35 (JSP20030) analog micro servos and 1 JR RT88 (JSP20080) retract servo—25-sized warbird 
• 4 JR MC35 (JSP20030) analog micro servos—15-sized 
sport aerobatic 
• 6 JR SPORT MN48 (JSP20040) analog mini servos—E-flite Ultra Stick 25 ARF & 15-size sport plane 
• 4 Spektrum DSP75 (SPMDSP75) digital programmable super sub micro servos-E-flite Ultimate 20-300 10e ARF 

Some other brands and models of servos may have significantly higher current draw. Digital servos and binding servos of any kind typically have higher current draw. As a general rule, micro and sub-micro servos draw less current which may affect your servo usage as shown in the examples above. We recommend the use of a Hangar 9 Servo and Receiver Current Meter (HAN172), installed between the throttle lead of the ESC and receiver, to confirm current draw of the actual servos used. Also, always 
be sure to position the ESC for maximum airflow since cooling can significantly aid in the performance of the BEC. 

Before first use, please refer to “Servo Ratings with BEC Enabled” notes for BEC usage guidelines. You must follow these guidelines for safe operation. If you are using more than 7 analog standard servos, more than 6 digital standard servos, or servos with higher current draw than the BEC can deliver, you will need to disable the BEC. If you wish to disable the BEC, you must remove the red receiver wire lead and connector from the receiver lead housing, and then insulate it properly to prevent shorting. When operating with the BEC disabled, E-flite recommends the use of a separate, high-power, external BEC (like the Ultimate BEC), or receiver pack and switch using the following items to ensure trouble-free operation: 

1. JR 1100mAh 4.8V Ni-MH receiver battery (JRPB4240), 
or similar 
2. JR Switch Harness (JRPA003), or similar